Return to Question

added 6 characters in body

edited Apr 20, 2021 at 23:51

I have very peculier problem. When I run this code SSD1306 fails to initialize. OutpuOutput at serial console is: 20:26:33.194 -> MPU6050 OLED demo 20

20:26:33.532 -> SSD1306 allocation failed

#include <Wire.h> #include <Adafruit_GFX.h> #include <Adafruit_MPU6050.h> #include <Adafruit_SSD1306.h> #include <Adafruit_Sensor.h> #define SCREEN_WIDTH 128 // OLED display width, in pixels #define SCREEN_HEIGHT 64 // OLED display height, in pixels #define OLED_RESET 4 // Reset pin # (or -1 if sharing Arduino reset pin) #define SCREEN_ADDRESS 0x3D ///< See datasheet for Address; 0x3D for 128x64, 0x3C for 128x32 Adafruit_MPU6050 mpu; Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, OLED_RESET); int count =0; void setup() { Serial.begin(9600); while (!Serial); Serial.println("MPU6050 OLED demo"); if (!mpu.begin()) { Serial.println("Sensor init failed"); while (1) yield(); } //Serial.println("Found a MPU-6050 sensor"); // SSD1306_SWITCHCAPVCC = generate display voltage from 3.3V internally if (!display.begin(SSD1306_SWITCHCAPVCC, SCREEN_ADDRESS)) { // Address 0x3C for 128x32 Serial.println(F("SSD1306 allocation failed")); for (;;) ; // Don't proceed, loop forever } display.display(); delay(500); // Pause for 2 seconds display.setTextSize(1); display.setTextColor(WHITE); display.setRotation(0); } void loop() { sensors_event_t a, g, temp; mpu.getEvent(&a, &g, &temp); display.clearDisplay(); display.setCursor(0, 0); display.println("Accelerometer - m/s^2"); display.print(a.acceleration.x, 1); display.print(", "); display.print(a.acceleration.y, 1); display.print(", "); display.print(a.acceleration.z, 1); display.println(""); display.println("Gyroscope - rps"); display.print(g.gyro.x, 1); display.print(", "); display.print(g.gyro.y, 1); display.print(", "); display.print(g.gyro.z, 1); display.println(""); display.display(); delay(100); }

#include <Wire.h> #include <Adafruit_GFX.h> #include <Adafruit_MPU6050.h> #include <Adafruit_SSD1306.h> #include <Adafruit_Sensor.h> #define SCREEN_WIDTH 128 // OLED display width, in pixels #define SCREEN_HEIGHT 64 // OLED display height, in pixels #define OLED_RESET 4 // Reset pin # (or -1 if sharing Arduino reset pin) #define SCREEN_ADDRESS 0x3D ///< See datasheet for Address; 0x3D for 128x64, 0x3C for 128x32 Adafruit_MPU6050 mpu; Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, OLED_RESET); int count =0; void setup() { //Serial.begin(9600); //while (!Serial); //Serial.println("MPU6050 OLED demo"); if (!mpu.begin()) { //Serial.println("Sensor init failed"); while (1) yield(); } //Serial.println("Found a MPU-6050 sensor"); // SSD1306_SWITCHCAPVCC = generate display voltage from 3.3V internally if (!display.begin(SSD1306_SWITCHCAPVCC, SCREEN_ADDRESS)) { // Address 0x3C for 128x32 Serial.println(F("SSD1306 allocation failed")); for (;;) ; // Don't proceed, loop forever } display.display(); delay(500); // Pause for 2 seconds display.setTextSize(1); display.setTextColor(WHITE); display.setRotation(0); } void loop() { sensors_event_t a, g, temp; mpu.getEvent(&a, &g, &temp); display.clearDisplay(); display.setCursor(0, 0); display.println("Accelerometer - m/s^2"); display.print(a.acceleration.x, 1); display.print(", "); display.print(a.acceleration.y, 1); display.print(", "); display.print(a.acceleration.z, 1); display.println(""); display.println("Gyroscope - rps"); display.print(g.gyro.x, 1); display.print(", "); display.print(g.gyro.y, 1); display.print(", "); display.print(g.gyro.z, 1); display.println(""); display.display(); delay(100); }

I have very peculier problem. When I run this code SSD1306 fails to initialize. Outpu at serial console is: 20:26:33.194 -> MPU6050 OLED demo 20:26:33.532 -> SSD1306 allocation failed

#include <Wire.h> #include <Adafruit_GFX.h> #include <Adafruit_MPU6050.h> #include <Adafruit_SSD1306.h> #include <Adafruit_Sensor.h> #define SCREEN_WIDTH 128 // OLED display width, in pixels #define SCREEN_HEIGHT 64 // OLED display height, in pixels #define OLED_RESET 4 // Reset pin # (or -1 if sharing Arduino reset pin) #define SCREEN_ADDRESS 0x3D ///< See datasheet for Address; 0x3D for 128x64, 0x3C for 128x32 Adafruit_MPU6050 mpu; Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, OLED_RESET); int count =0; void setup() { Serial.begin(9600); while (!Serial); Serial.println("MPU6050 OLED demo"); if (!mpu.begin()) { Serial.println("Sensor init failed"); while (1) yield(); } //Serial.println("Found a MPU-6050 sensor"); // SSD1306_SWITCHCAPVCC = generate display voltage from 3.3V internally if (!display.begin(SSD1306_SWITCHCAPVCC, SCREEN_ADDRESS)) { // Address 0x3C for 128x32 Serial.println(F("SSD1306 allocation failed")); for (;;) ; // Don't proceed, loop forever } display.display(); delay(500); // Pause for 2 seconds display.setTextSize(1); display.setTextColor(WHITE); display.setRotation(0); } void loop() { sensors_event_t a, g, temp; mpu.getEvent(&a, &g, &temp); display.clearDisplay(); display.setCursor(0, 0); display.println("Accelerometer - m/s^2"); display.print(a.acceleration.x, 1); display.print(", "); display.print(a.acceleration.y, 1); display.print(", "); display.print(a.acceleration.z, 1); display.println(""); display.println("Gyroscope - rps"); display.print(g.gyro.x, 1); display.print(", "); display.print(g.gyro.y, 1); display.print(", "); display.print(g.gyro.z, 1); display.println(""); display.display(); delay(100); }

#include <Wire.h> #include <Adafruit_GFX.h> #include <Adafruit_MPU6050.h> #include <Adafruit_SSD1306.h> #include <Adafruit_Sensor.h> #define SCREEN_WIDTH 128 // OLED display width, in pixels #define SCREEN_HEIGHT 64 // OLED display height, in pixels #define OLED_RESET 4 // Reset pin # (or -1 if sharing Arduino reset pin) #define SCREEN_ADDRESS 0x3D ///< See datasheet for Address; 0x3D for 128x64, 0x3C for 128x32 Adafruit_MPU6050 mpu; Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, OLED_RESET); int count =0; void setup() { Serial.begin(9600); while (!Serial); Serial.println("MPU6050 OLED demo"); if (!mpu.begin()) { Serial.println("Sensor init failed"); while (1) yield(); } //Serial.println("Found a MPU-6050 sensor"); // SSD1306_SWITCHCAPVCC = generate display voltage from 3.3V internally if (!display.begin(SSD1306_SWITCHCAPVCC, SCREEN_ADDRESS)) { // Address 0x3C for 128x32 Serial.println(F("SSD1306 allocation failed")); for (;;) ; // Don't proceed, loop forever } display.display(); delay(500); // Pause for 2 seconds display.setTextSize(1); display.setTextColor(WHITE); display.setRotation(0); } void loop() { sensors_event_t a, g, temp; mpu.getEvent(&a, &g, &temp); display.clearDisplay(); display.setCursor(0, 0); display.println("Accelerometer - m/s^2"); display.print(a.acceleration.x, 1); display.print(", "); display.print(a.acceleration.y, 1); display.print(", "); display.print(a.acceleration.z, 1); display.println(""); display.println("Gyroscope - rps"); display.print(g.gyro.x, 1); display.print(", "); display.print(g.gyro.y, 1); display.print(", "); display.print(g.gyro.z, 1); display.println(""); display.display(); delay(100); }

I have very peculier problem. When I run this code SSD1306 fails to initialize. Output at serial console is: 20:26:33.194 -> MPU6050 OLED demo

20:26:33.532 -> SSD1306 allocation failed

#include <Wire.h> #include <Adafruit_GFX.h> #include <Adafruit_MPU6050.h> #include <Adafruit_SSD1306.h> #include <Adafruit_Sensor.h> #define SCREEN_WIDTH 128 // OLED display width, in pixels #define SCREEN_HEIGHT 64 // OLED display height, in pixels #define OLED_RESET 4 // Reset pin # (or -1 if sharing Arduino reset pin) #define SCREEN_ADDRESS 0x3D ///< See datasheet for Address; 0x3D for 128x64, 0x3C for 128x32 Adafruit_MPU6050 mpu; Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, OLED_RESET); int count =0; void setup() { Serial.begin(9600); while (!Serial); Serial.println("MPU6050 OLED demo"); if (!mpu.begin()) { Serial.println("Sensor init failed"); while (1) yield(); } Serial.println("Found a MPU-6050 sensor"); // SSD1306_SWITCHCAPVCC = generate display voltage from 3.3V internally if (!display.begin(SSD1306_SWITCHCAPVCC, SCREEN_ADDRESS)) { // Address 0x3C for 128x32 Serial.println(F("SSD1306 allocation failed")); for (;;) ; // Don't proceed, loop forever } display.display(); delay(500); // Pause for 2 seconds display.setTextSize(1); display.setTextColor(WHITE); display.setRotation(0); } void loop() { sensors_event_t a, g, temp; mpu.getEvent(&a, &g, &temp); display.clearDisplay(); display.setCursor(0, 0); display.println("Accelerometer - m/s^2"); display.print(a.acceleration.x, 1); display.print(", "); display.print(a.acceleration.y, 1); display.print(", "); display.print(a.acceleration.z, 1); display.println(""); display.println("Gyroscope - rps"); display.print(g.gyro.x, 1); display.print(", "); display.print(g.gyro.y, 1); display.print(", "); display.print(g.gyro.z, 1); display.println(""); display.display(); delay(100); }

#include <Wire.h> #include <Adafruit_GFX.h> #include <Adafruit_MPU6050.h> #include <Adafruit_SSD1306.h> #include <Adafruit_Sensor.h> #define SCREEN_WIDTH 128 // OLED display width, in pixels #define SCREEN_HEIGHT 64 // OLED display height, in pixels #define OLED_RESET 4 // Reset pin # (or -1 if sharing Arduino reset pin) #define SCREEN_ADDRESS 0x3D ///< See datasheet for Address; 0x3D for 128x64, 0x3C for 128x32 Adafruit_MPU6050 mpu; Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, OLED_RESET); int count =0; void setup() { //Serial.begin(9600); //while (!Serial); //Serial.println("MPU6050 OLED demo"); if (!mpu.begin()) { //Serial.println("Sensor init failed"); while (1) yield(); } //Serial.println("Found a MPU-6050 sensor"); // SSD1306_SWITCHCAPVCC = generate display voltage from 3.3V internally if (!display.begin(SSD1306_SWITCHCAPVCC, SCREEN_ADDRESS)) { // Address 0x3C for 128x32 Serial.println(F("SSD1306 allocation failed")); for (;;) ; // Don't proceed, loop forever } display.display(); delay(500); // Pause for 2 seconds display.setTextSize(1); display.setTextColor(WHITE); display.setRotation(0); } void loop() { sensors_event_t a, g, temp; mpu.getEvent(&a, &g, &temp); display.clearDisplay(); display.setCursor(0, 0); display.println("Accelerometer - m/s^2"); display.print(a.acceleration.x, 1); display.print(", "); display.print(a.acceleration.y, 1); display.print(", "); display.print(a.acceleration.z, 1); display.println(""); display.println("Gyroscope - rps"); display.print(g.gyro.x, 1); display.print(", "); display.print(g.gyro.y, 1); display.print(", "); display.print(g.gyro.z, 1); display.println(""); display.display(); delay(100); }

Source Link

asked Apr 20, 2021 at 15:21

Pankaj

Serial and I2C not working together

I have very peculier problem. When I run this code SSD1306 fails to initialize. Outpu at serial console is: 20:26:33.194 -> MPU6050 OLED demo 20:26:33.532 -> SSD1306 allocation failed

#include <Wire.h> #include <Adafruit_GFX.h> #include <Adafruit_MPU6050.h> #include <Adafruit_SSD1306.h> #include <Adafruit_Sensor.h> #define SCREEN_WIDTH 128 // OLED display width, in pixels #define SCREEN_HEIGHT 64 // OLED display height, in pixels #define OLED_RESET 4 // Reset pin # (or -1 if sharing Arduino reset pin) #define SCREEN_ADDRESS 0x3D ///< See datasheet for Address; 0x3D for 128x64, 0x3C for 128x32 Adafruit_MPU6050 mpu; Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, OLED_RESET); int count =0; void setup() { Serial.begin(9600); while (!Serial); Serial.println("MPU6050 OLED demo"); if (!mpu.begin()) { Serial.println("Sensor init failed"); while (1) yield(); } //Serial.println("Found a MPU-6050 sensor"); // SSD1306_SWITCHCAPVCC = generate display voltage from 3.3V internally if (!display.begin(SSD1306_SWITCHCAPVCC, SCREEN_ADDRESS)) { // Address 0x3C for 128x32 Serial.println(F("SSD1306 allocation failed")); for (;;) ; // Don't proceed, loop forever } display.display(); delay(500); // Pause for 2 seconds display.setTextSize(1); display.setTextColor(WHITE); display.setRotation(0); } void loop() { sensors_event_t a, g, temp; mpu.getEvent(&a, &g, &temp); display.clearDisplay(); display.setCursor(0, 0); display.println("Accelerometer - m/s^2"); display.print(a.acceleration.x, 1); display.print(", "); display.print(a.acceleration.y, 1); display.print(", "); display.print(a.acceleration.z, 1); display.println(""); display.println("Gyroscope - rps"); display.print(g.gyro.x, 1); display.print(", "); display.print(g.gyro.y, 1); display.print(", "); display.print(g.gyro.z, 1); display.println(""); display.display(); delay(100); }

But when I run this code, without displaying gyro everything runs fine. Adafruit logo is displayed and then followed by regular accelerometer data.

#include <Wire.h> #include <Adafruit_GFX.h> #include <Adafruit_MPU6050.h> #include <Adafruit_SSD1306.h> #include <Adafruit_Sensor.h> #define SCREEN_WIDTH 128 // OLED display width, in pixels #define SCREEN_HEIGHT 64 // OLED display height, in pixels #define OLED_RESET 4 // Reset pin # (or -1 if sharing Arduino reset pin) #define SCREEN_ADDRESS 0x3D ///< See datasheet for Address; 0x3D for 128x64, 0x3C for 128x32 Adafruit_MPU6050 mpu; Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, OLED_RESET); int count =0; void setup() { Serial.begin(9600); while (!Serial); Serial.println("MPU6050 OLED demo"); if (!mpu.begin()) { Serial.println("Sensor init failed"); while (1) yield(); } //Serial.println("Found a MPU-6050 sensor"); // SSD1306_SWITCHCAPVCC = generate display voltage from 3.3V internally if (!display.begin(SSD1306_SWITCHCAPVCC, SCREEN_ADDRESS)) { // Address 0x3C for 128x32 Serial.println(F("SSD1306 allocation failed")); for (;;) ; // Don't proceed, loop forever } display.display(); delay(500); // Pause for 2 seconds display.setTextSize(1); display.setTextColor(WHITE); display.setRotation(0); } void loop() { sensors_event_t a, g, temp; mpu.getEvent(&a, &g, &temp); display.clearDisplay(); display.setCursor(0, 0); display.println("Accelerometer - m/s^2"); display.print(a.acceleration.x, 1); display.print(", "); display.print(a.acceleration.y, 1); display.print(", "); display.print(a.acceleration.z, 1); display.println(""); display.println("Gyroscope - rps"); display.print(g.gyro.x, 1); display.print(", "); display.print(g.gyro.y, 1); display.print(", "); display.print(g.gyro.z, 1); display.println(""); display.display(); delay(100); }

Now, while debugging when I disable Serial logs and comment all Serial.print then the above code runs properly, logo is displayed, accelerometer and gyro both the data are displayed on OLED properly.

Compiler Log for non-working code is: Sketch uses 21980 bytes (71%) of program storage space. Maximum is 30720 bytes. Global variables use 761 bytes (37%) of dynamic memory, leaving 1287 bytes for local variables. Maximum is 2048 bytes.

The setup I am using as Arduino Nano, MPU6050 connected over I2C (address 0x68), SSD1306 based 0.96" 128x64 display over I2C (address 0x3D). I am using A4 and A5 pin of Arduino Nano as I2C. Both device are connected over same bus. I am using breadboard for testing.

PS: Both the code compiles without error or warning