Skip to main content

Questions tagged [modem]

Discussion of retrocomputing modems.

7 votes
0 answers
190 views

Problem Statement I am trying to run AppleTalk over PPP on a Cisco 3845 router accepting incoming PPP connections so that old Macintosh computers can connect via dialup to the rest of my AppleTalk ...
Juffo-Wup's user avatar
11 votes
2 answers
634 views

I recall in the early 90s a type of modem (for analog phone lines) that let you conduct a voice call while maintaining a data connection. It sent bursts of data during the natural silences in ...
Tankboy's user avatar
  • 130
3 votes
3 answers
827 views

Typically, an ISA dial-up modem card has two RJ11 jacks: one labeled Telco and the other labeled Line or Phone, intended to be connected to a telephone. Normally, when issuing commands to the modem to ...
Sung's user avatar
  • 791
4 votes
1 answer
169 views

My very first modem was an Avatex 1200 connected to my trusty C64. Unfortunately, the power adapter has long since been, let's say, disassociated from the hardware. I probably still have it, but the ...
Geo...'s user avatar
  • 11k
20 votes
3 answers
3k views

I've had a Hayes Micromodem II for the Apple ][ a very, very long time. I've seen a lot of interface cards over the years since then and have never seen anything quite like it: there are giant orange, ...
bjb's user avatar
  • 19.1k
5 votes
4 answers
744 views

As home computers rapidly gained in popularity in the early 1980s, third-party peripheral manufacturers also began selling peripherals. For those users wanting to do "serious work", the ...
Brian H's user avatar
  • 62.1k
5 votes
2 answers
905 views

Many hotel etc phones plug into a digital PBX, often with a non-standard interface. Does the interface PBX phones plug into limit modem speed to below 56k?
Yuhong Bao's user avatar
17 votes
4 answers
2k views

In 1997, there was this service called Wireplay in the UK. Instead of using the Internet, you used it by directly phoning their servers with your modem from your PC, and the point of this was that it ...
Rosero's user avatar
  • 171
9 votes
4 answers
2k views

While both were data transfer protocols serving streams at 300/1200 baud, why did they choose different frequencies, marks, modulation, and anything else? I understand that they serve different ...
Schezuk's user avatar
  • 3,834
6 votes
3 answers
1k views

I'd like to run an old-school BBS that can be dialed into over a real phone line. Unfortunately, I don't currently have the necessary hardware to do so. I had the idea of purchasing a VPS and then ...
Caden Snyder's user avatar
11 votes
2 answers
1k views

The Bell 103 modem spec gives the following frequencies to use: Transmit Side: 1070Hz (space) and 1270Hz (mark) Receive Side: 2025Hz (space) and 2225Hz (mark) Why were these specific frequencies ...
Ben Longo's user avatar
  • 210
4 votes
4 answers
1k views

I am quite a newbie to retrocomputing, and I don't know if such a question should be asked here. But I hope maybe some of you could help me. I started reflecting on ways to send data without the ...
Julien's user avatar
  • 41
7 votes
2 answers
701 views

I'm working on my ultimate CDTV setup, few hiccups along the way with CDROM access on TF536, but we will cross this bridge. As of right now I'm only missing and internet access, before I can finally ...
Bartek Malysz's user avatar
34 votes
6 answers
6k views

All the technology in my house is modern, but I want to build a dialup network that I can use to produce sounds from Bell 101/103 (if I can find the proper softmodem) to V.92bis. I honestly don't know ...
jediKatana's user avatar
26 votes
7 answers
5k views

In 1997, my uncle visited and gave me a "fax modem" which he installed on our 486 PC and then managed to transfer over a fax document from a real fax in his home to our computer, running ...
user avatar

15 30 50 per page