Questions tagged [usbasp]
The usbasp tag has no summary.
18 questions
4 votes
1 answer
794 views
Can not burn arduino pro mini 8 MHz bootloader with usbasp
I am using schematic of Arduino Pro mini 3.3v/8 MHz version. Please see below circuit diagram I built. Power supply to circuit is 3.3V. I have a USB ASP programmer which I used in previous version of ...
- 61
3 votes
1 answer
2k views
Expected signature for ATmega328P is 1E 95 0F; I can not burn bootloader on my arduino Uno
well... the problem starts from the time that I accidentally touched the crystal on my arduino and all of a sudden everything messed up; the leds on arduino turned on and off while being touched, and ...
- 31
1 vote
1 answer
127 views
Custom 328P-AU board not responding via ICSP
I created a custom PCB based on a 328P. The design is mainly based on the Arduino Nano schematic (3.0). The boards have arrived some days ago, and I can't get avrdude to recognize them via USBASP (or ...
- 123
-1 votes
1 answer
1k views
Why ATMEGA328P U-TH doesn't answer to USBasp but work fine with Arduino as ISP?
I ordered ATMEGA328P AU from China recent but I got "ATMEGA328P U-TH". which seem super problematic. I try to use USBasp to burn bootloader but it fail and show error message as shown. ...
- 131
1 vote
0 answers
219 views
How to burn a bootloader to non-bootloaded(clean crystal) ATMEGA328P-PU with USBASP programmer via Avrdudess?
I'm trying to burn bootloader to my clean crystals, atmega328p-pu.For this I use the 16MHZ crystal with two ceramic capacitors and USBASP programmer, on Windows 10 Pro. As program for burning I tried: ...
- 11
-1 votes
1 answer
418 views
Error while reburning bootloader to atmega328p by usbasp in Arduino IDE
I have got the Bootloaded ATMega328P-PU from China and I want to reburn new bootloader into it. For this I use UsbAsp programmer. I want to do it in Arduino IDE. But when I try to flash, for example, ...
- 11
1 vote
0 answers
57 views
Mistaken Connect 5V to SCK Pin
i have old chinese old hotair station that controls by atmega8l 8ua chip.. and the board designer are clever enough to put 2 identical dc plug, 1 is 5v supply cable.. the other one is on off switch ...
- 11
1 vote
1 answer
497 views
Usbasp Arduino Uno Bootloader Flash Error - Win 10
I'm trying to flash an Arduino Uno using usbasp but i'm getting the following error,I have checked all the connection and voltage using multimeter but still this error: Arduino: 1.8.8 (Windows 10), ...
- 61
1 vote
0 answers
1k views
how to fix USBASP Unknown USB Device (device descriptor request failed) - Win 10?
I just recently purchased Usbasp from Ali Express, when i'm connecting it to the windows 10 desktop in device manager its Unknown USB Device (device descriptor request failed). How to fix this error? ...
- 61
1 vote
1 answer
194 views
Transmit image file thougth the TX TR serial line
I have a digital camera with a USB port for image dowload from the camera SD card. I will like to be able to capture this image files store in the camera SD card using the Arduino TX TR lines (...
2 votes
0 answers
382 views
Atmega 32U4 doesn't show on device manager after fuse bits reset
I am finally ready to try setting fuse bits on my ATMega32u4-AU custom board (8Mhz Ceramic Resonators, 3.3V), however, after I set the fuse bits and plug my board to computer, the device manager ...
- 21
1 vote
1 answer
415 views
ATmega328P of Arduino Pro Mini not responding
While I was trying to change the fuse bits of ATmega328P of my Arduino pro mini using a USBasp device to operate it at 3.3 V/8 MHz, it failed due to the bad connection I guess. After that, ...
2 votes
0 answers
747 views
Arduino nano stk500_getsync() attempt 1 of 10: not in sync: resp=0xe1
I have been building a project using an arduino nano clone. It uses the CH340 chip. It worked perfectly, and a week later it now doesnt. When I want to upload code in arduino IDE I get the error ...
2 votes
0 answers
113 views
Can I upload with avrdude 2 hexes with 2 usbasp connected to computer, one hex with one usbasp ? If yes, how?
If I have connected 2 usbasps in the same time to ubuntu, can I upload 2 hexes one after the other(using avrdude) on each usbasp without disconnecting a usbasp ? If yes, how do I select each port for ...
0 votes
1 answer
803 views
Can i burn an Arduino sketch .hex directly using USBASP?
I am unable to upload sketches to my Arduino Uno board using the upload option in the IDE. I have done quite a few tests to find the reason but everything seems to be working fine when tested ...
- 103