Skip to main content
Electrical Engineering

All Questions

Ask Question
Tagged with or
4,778 questions
Newest Active Bountied Unanswered
1 vote
2 answers
66 views

I am using a resistor divider of 523 kΩ on the high side and 10 kΩ on the low side. Using an STM32 microcontroller to read the voltage of the supply. How is the voltage actually being converted to ADC ...
Gokul Karthik's user avatar
  • 521
0 votes
0 answers
35 views

Interfacing SDcard with stm32 using Spi interface, sdcard is of 16gb ,and while storing json files to sdcard it stores upto 50 files in faster rate but after 50-60 files the rate of storing files ...
Shubham's user avatar
  • 1
0 votes
1 answer
60 views

I am currently working on an stm32-based design. I am trying to understand how to power the stm32 through USB. We came up with the following solution: The idea is that +3v3_power is the main rail of ...
jazam's user avatar
  • 1
2 votes
1 answer
74 views

I am designing a system where I have several daughter boards with voltage or current sensors (several or one on each board). One board is the master with the MCU. Because the system is larger and in a ...
miha medved's user avatar
  • 123
0 votes
0 answers
67 views

I am using a bluepill, and the final case statement is looping constantly from GO_TO_TOP -> COME_TO BOTTOM -> ROTATE_ACTION, the 'top' variable is being latched to '1' at the GO_TO_TOP case ...
Samartha Rao HP's user avatar
  • 1
-1 votes
1 answer
63 views

I want to write an application for stm32h573 that uses a single HAL for a combination of peripherals that are not all used in the same STM32Cube example. However, ...
personal_cloud's user avatar
  • 796
-1 votes
0 answers
35 views

I am trying to configure U-Boot on a stm32mp257f-dk board so that I can use the “ums” command with SuperSpeed. After configuring the device tree, I managed to configure the usb3dr as usb3(as it says ...
Axom's user avatar
  • 1
0 votes
1 answer
100 views

As demonstrated by the image above, blocks are displayed on the LCD1, even though I've configured and programmed the Blue Pill STM32F103C8T6 board and connected it ...
Reza Jaferi's user avatar
  • 27
0 votes
0 answers
29 views

I am working with the STM32WL55CC (48-pin package). When I imported the official STM32CubeWL example projects from ST, I noticed that they provide both SINGLE CORE and DUAL CORE versions. But the ...
Aryan's user avatar
  • 21
0 votes
0 answers
47 views

I have an MCU connected to external SRAM (the SRAM powered from battery only and the MCU from another constant supply). The interface to SRAM is QSPI with max frequency of 104MHz. I can't guarantee ...
Knowledge's user avatar
  • 553
-1 votes
1 answer
134 views

I just wanna ask about the rest push button connection. Are there technological reasons for making it active low and not active high?
AHMED FAWZI AHMED FEDEIL T24KE's user avatar
  • 7
2 votes
2 answers
328 views

I'm running three tasks using STM32 RTOS v2. I want to know the time difference between button presses, so I've configured it as follows: ...
humni's user avatar
  • 129
0 votes
1 answer
96 views

I have been attempting to get f_write to work on an SD card through SPI with an STM32L432KC using Elm Chan's code as a base. The error I am getting is FR_DISK_ERR ...
Ethan Fredsti's user avatar
  • 41
0 votes
1 answer
76 views

Here is my setup STM32F401CCU6 WeAct Blackpill, which controls A 3.3V-24V Optocoupler, which controls A Siemens 3-phase contactor to switch a 400VAC induction motor, with flyback diode on the ...
a_communist_comrade's user avatar
  • 9
-3 votes
1 answer
96 views

I need to control an N-channel power MOSFET (STD12NF06LT4), but the micro STM32F446 cannot do it by connecting the pin directly to the gate. I've heard about PMOS controlling NMOS but I can't find ...
Riccardo Catalanotti's user avatar
  • 1

15 30 50 per page
1
2 3 4 5
…
319