Questions tagged [cable]

Question 1

I own a Raspberry Pi 4B and I decided to turn it into a NAS. I recently bought a Geekworm NASPi v2.0 kit, which includes a PWM-controllable fan (X823-A3), a 2.5" SATA shield (X823), an adapter ...

Question 2

I've been successfully powering my pi 5 from a power bank with no converters (with no peripherals except the fan and a usb wifi adapter). But the behavior I've observed is very strange. That power ...

Question 3

I've bought a 64x64 LED Matrix Display, an Adafruit bonnet and a Raspberry Pi 4 2Gb. I have set everything up and tested the Display and set all pixels to red. But only the first and the third quarter ...

Question 4

So I have a Raspberry Pi 4 type C 5V 3A adapter plugged into the power extender thingy at all times. My question is, once you type the poweroff command into the terminal and see the device turning off,...

Question 5

New to this. I bought a pi-4 kit. It has dual heatsink fans that get connected to pin 4 and 6. however, I want to do other projects and need to connect a ribbon cable to it. how can i do that while ...

Question 6

I bought new raspberry pi 4 with 8 GB ram, and it behaves strange- while it has connected external usb drive, which has it's separate power supply and I power up rpi, it doesn't connect to the local ...

Question 7

So I have a Pi 4 and an official touchscreen and I'm building a portable device to run retropie. I got a heatsink/fan combo which is about as tall as the USBs on the pi and I've ordered a Pi Juice HAT ...

Question 8

i was wondering if it may be usefull to have a protection for the flex cable of the picam. My picam will work in really dusty area. I can't find any hardware protection for this cable (or maybe i ...

Question 9

I have an old tablet Galaxy Tab GT-P1000 and I would like to ask if it could be possible to connect to raspberry? Size of flex cable looks similar... Amazon

Question 10

Is there a type of extender for the official Pi display connections? I don't mean the 15 pin FFC, but the two directly on the display. I'm mounting the driver board separately from the display in a ...

Question 11

weird question, i am sure but there is a good reason. We have a bike rack at the back of our van and when we drive I see poorly out the back. I have to use the side mirrors when of course the middle ...

Question 12

My teacher gave me a large group of jumper cables attached to one another. this might be a stupid question but if it's attached like on the on the bottom picture what is the order of the cables? (...

Question 13

So I want to wire two DHT22 sensors (5V) to a Pi and also control a lightbulb with 220V. As a plus this should be very compact and I don't want to solder or use breadboards/jumper cabling. I looked ...

Question 14

I have this barcode scanner module and I need to connect it to my raspberry pi 3 b+. I am a beginner at this and I don't know how to go about it. I have been searching for weeks. The seller in ...

Question 15

I'm planing on putting up a magnet and a reed switch on my window at home and I'm planing on using a RaspberryPi to sense when it's open/closed. I'm going to pull the wire up in the attic so the ...

Stack Exchange Network

Questions tagged [cable]

Is this I2C setup going to fry my Raspberry?

Can the Pi 5 run on just 1 Amp?

Pi with LED Matrix not working properly

After shutdown/poweroff command, is it possible to damage a pi (4) by leaving the Powercable in?

Pi-4 with fans and ribbon cable

My LAN cable connection doesn't work, when I have usb drive plugged

Can I use a 40 pin GPIO ribbon cable to connect a Pi 4 to a Pi Juice?

How to protect picam flex cable?

Connect flex cable to raspberry

Extend Official Display Connections

Raspberry Pi Dashcam feed cable through closed car door?

Connecting jumpercable to gpio pins

How to use a stackable Rpi relay HAT to control 220V AC mains power?

FFC 12 pin cable with a USB interface

Max distance for GPIO cable? [duplicate]

Hot Network Questions