Skip to main content
3D Printing

Questions tagged [automatic-bed-leveling]

Ask Question

Use this tag for questions regarding the automatic leveling of the build platform.

23 questions
Newest Active Bountied Unanswered
0 votes
1 answer
142 views

First off, I apologize greatly for the vagueness of my question. However I hope you are at least willing to give advice. Many months ago, I was performing a repair on my Sovol SV08. However, due to my ...
Michael Sohnen's user avatar
  • 63
0 votes
1 answer
226 views

I recently obtained a used Creality CR-10S Pro V2. This is my first 3D printer, so there's a lot to learn. The firmware is stock and up to date. I have an occasional issue where sometimes when homing, ...
Ogre's user avatar
  • 101
1 vote
0 answers
21 views

I bought an Ender 3 v2 off a friend because he wanted to upgrade and I wanted to try getting into 3D printing (slightly relevant). He had a few upgrades on it, including a BLTouch. I printed 2 prints ...
Doragon's user avatar
  • 111
1 vote
2 answers
1k views

I just upgraded an original CR-10 with the CRTouch bed leveling sensor and upgraded the firmware from stock to Marlin. In the CURA slicer, I added a preamble to every print to perform bed leveling. ...
st2000's user avatar
  • 171
1 vote
1 answer
138 views

I have this case uneven defect on print when using Anycubic Kobra, it occurs from the first layer. I use 0.6 nozzle and all the default features. Here're the actions that I already tried: Built-in ...
DrPortgas's user avatar
  • 51
0 votes
1 answer
539 views

I do have an Ender-3-Pro with the Sprite Extruder Pro on it. Also, I swapped out the controller board for a BigTreeTech SKR 1.4 Turbo, which works perfectly for me. I am using the CR Touch to level ...
XaniXxable's user avatar
  • 1
1 vote
2 answers
2k views

What are the differences between the bed leveling probes BLTouch, CRTouch and 3DTouch in terms of reliability and accuracy? Is there some kind of benchmark available? Also, how often should the ...
Bob Ortiz's user avatar
  • 1,255
3 votes
1 answer
811 views

I just discovered automatic bed leveling (ABL) probes that only use a microswitch. For example, the FreeABL as shown below: Source: Thingiverse.com Or, the magnet mounted KlackEnder as shown below: ...
Bob Ortiz's user avatar
  • 1,255
2 votes
2 answers
4k views

The Creality Ender 3 V3 SE, apart from auto bed leveling (ABL), also has a way to calculate the Z-offset automatically. A feature I didn't hear about before. According to a Maker's Muse video, it's ...
Bob Ortiz's user avatar
  • 1,255
1 vote
1 answer
433 views

Recently added a probe to my Anet A8 for auto bed levelling, calculations have been added based on position of probe to hotend as required. I'm using Marlin 1.1.9. When I go into 'Prepare' in the ...
Raynbow's user avatar
  • 13
1 vote
1 answer
1k views

I recently started using the new mriscoc firmware for my Creality Ender 3 V2 and it is truly performing above expectations. Even considering that Jyers UI was already a step up from the original ...
Bob Ortiz's user avatar
  • 1,255
1 vote
2 answers
675 views

Yesterday I was printing just fine. Today I put the new springs that I bought from Amazon. Swapped them out, went to level things and my Z-offset was of course way off. I have the ...
Joleme's user avatar
  • 21
0 votes
1 answer
2k views

I have been printing on and off for years. Generally, I have had no issues until recently. Upon thinking back I don't think I used the Z-offset at any point and only manually leveled my Ender 3 S1 Pro....
Nolan Robidoux's user avatar
  • 193
0 votes
1 answer
158 views

I should mention that this is my experience with Marlin. I can adjust the Z offset all I want in the UI, but not the X/Y offset. If you reinstall the probe, I've heard you may need to adjust the Z ...
Octanum's user avatar
  • 15
1 vote
0 answers
2k views

When I first bought the Ender 3 S1 Pro, everything worked fine, but at some point, the auto-leveling stopped working. I used to manually level it every dozen or so prints (sheet of paper method) just ...
William Byrd's user avatar
  • 11

15 30 50 per page
1
2