Questions tagged [homing]
For questions regarding the "homing" (positioning to a known location) of 3D printing devices.
54 questions
1 vote
1 answer
87 views
Ender 3 V2 Neo Loses Homing
After successful Auto Homing, my Ender 3 V2 Neo loses homing and the print nozzle drops from whatever Z-axis position down to the bed. This happens after 2 minutes of inactivity. The X, Y and Z values ...
- 113
0 votes
1 answer
226 views
How to properly maintain BLTouch probe?
I recently obtained a used Creality CR-10S Pro V2. This is my first 3D printer, so there's a lot to learn. The firmware is stock and up to date. I have an occasional issue where sometimes when homing, ...
- 101
0 votes
0 answers
273 views
How does the homing work on Creality K1 Max?
After playing with shims I was able to reach a good tradeoff with bed leveling: I rotated the image to better show what I mean: the right side of the picture is the back of the printer, where there ...
- 509
0 votes
0 answers
82 views
Printer homes X, Y then Z in the middle of the bed, but then sets the origin to the middle of the bed
I have a Creality CR10-S5. It homes the X and Y axes then homes to Z in the middle of the bed. The origin location is set at the front left of the bed. It homes great, but it also resets the origin ...
0 votes
0 answers
26 views
Define X_AFTER_HOMING for X axis? [duplicate]
I am just trying to get to understand how to solve an X-axis off-plate problem. I am on Marlin 2.1.2.4 paired with Repetier. What is currently happening to me is that when homing the axes, the nozzle ...
0 votes
1 answer
4k views
Error message "homing failed printer halted please reset"
I have an Ender 3 Pro 4.2.7 2.0.8.2 that I haven't used for a couple of months; switched it on, all perfect. I tried to print a model and the PLA wouldn't stick to the bed; I think the hotend was a ...
- 11
-1 votes
1 answer
676 views
Homing fails with filament in run-out sensor
My friend has an Ender 3 Max Neo that they were just able to reassemble after moving. Looking it over there didn’t seem to be any assembly errors, but the auto-home was definitely causing a few issues....
-1 votes
1 answer
199 views
Nozzle hitting bed corner before it stars printing
I just got this Artillery Hornet printer. I am new to the 3D printing but the printer is not new. The glass bed was leveled from the Marlin firmware menu (Motion > Bed leveling > Level corners) ...
- 1
0 votes
0 answers
136 views
Printer always homes X & Y at end of print
I can't figure out why, but at the end of every print, my Creality CR-10 Smart Pro will move the print head left until it hits the limit switch and move the bed back until it hits its limit switch. I ...
0 votes
0 answers
256 views
Steppers grinding when homing Marlin
When homing the 3D printer or running G29, the X & Y axes are grinding and not moving fully to the correct position. When I run the following G-code the print ...
- 123
0 votes
1 answer
916 views
AnkerMake M5 Z-axis homing fail
I recently had a big mess in my printer head in my AnkerMake M5 and had to replace the entire print head. When I replaced it, I went to test the axes to make sure they were still aligned, but now I'm ...
- 109
1 vote
1 answer
191 views
G28 X does not home the hotend
I have a classic Ender 3 running Marlin-2.1.1 on a BTT SKR v1.3 board with TMC 2130 drivers. Wifi is connected with ESP3D on an ESP32-CAM board connected to a TFT port. The X endstop is on the left ...
- 31
1 vote
1 answer
932 views
Auto Homing issue (Z-axis ignores endstop but individually homing each axis there is no problem)
I'm experiencing an issue with the auto homing where the Z-axis will ignore the endstop when I use the auto home button in Pronterface. Strangely, homing the axes individually I don't seem to have any ...
1 vote
0 answers
800 views
Anycubic Chiron homing issue
The Anycubic Chiron is the third 3D printer I’ve owned, so I’m fairly familiar with the inner workings of them. The problem occurs when I home the Z-axis. Once the Z-axis sensor gets triggered, the Z-...
- 21
2 votes
1 answer
2k views
Flashforge Adventurer 3 - how to replace X-axis endstop
I found a similar question in the forum but now need assistance on how to replace the X-axis endstop. I have been scouring for videos and haven't found one yet. Can anyone help me? The printer turns ...
